DAWES DEVICE NEXT ?????
28 February 2003, 10:48 PM
#64
Scooby Regular
Join Date: Dec 2002
Location: Sunny BELFAST
Posts: 19,408
Likes: 0
Received 0 Likes
on
0 Posts
no probs m8 whenever will suit me fine, i ain't going no where (car is being left in next week again for Adjustable fuel reg, knocklink and afr).
cheers
big sinky
cheers
big sinky
02 March 2003, 08:44 PM
#65
Prodrive Chip and a Dawes in a Pre97 MY will be very close if not already detonating
. Take the dawes OFF NOW !!!!!
It will more than likley be detonating if you are running more than 15psi.
Beleive me I know from experience...increasing the boost on Pre97 Prodrive fuel/Ignition Map = Detonation.
The Prodrive map is right on the limit of Detonation. If you really have to use a dawes, use it with the standard map (pull the chip out and add a wire link to the 'J1' position on the PCB)
Although low down will not be as good or as smooth on the standard map.
Get David to drop in a remapped chip... If it's the chip I think it is (15.5psi)
it should give you about 260ft/lb of torque in a UK car, with improved spool up and timing retarded in the top quarter to prevent Detonation....
Hmmm.... I seem to know alot about this subject....
. Take the dawes OFF NOW !!!!!It will more than likley be detonating if you are running more than 15psi.
Beleive me I know from experience...increasing the boost on Pre97 Prodrive fuel/Ignition Map = Detonation.
The Prodrive map is right on the limit of Detonation. If you really have to use a dawes, use it with the standard map (pull the chip out and add a wire link to the 'J1' position on the PCB)
Although low down will not be as good or as smooth on the standard map.
Get David to drop in a remapped chip... If it's the chip I think it is (15.5psi)
it should give you about 260ft/lb of torque in a UK car, with improved spool up and timing retarded in the top quarter to prevent Detonation....Hmmm.... I seem to know alot about this subject
....
05 March 2003, 03:30 PM
#69
Scooby Regular
Join Date: Aug 2002
Posts: 171
Likes: 0
Received 0 Likes
on
0 Posts
Hi,
I have read through this thread and have to ask one thing, Will I be safe putting a Dawes device on MY99 uk turbo my mods are below.
Decat Centre
SS back box
Forge DV
ITG panel filter
If I am good to go I will need to buy metres to measure stats, I want to get hold of the Metres that Sit in that middle console up on the front dash(three metre's in a row), Where can I get them from? and Where canI get a dawes supplied and fitted?
Thanks
Ryan
P.S Sorry Alan for stepping in on your topic but this looks like a good place to put my question in.
I have read through this thread and have to ask one thing, Will I be safe putting a Dawes device on MY99 uk turbo my mods are below.
Decat Centre
SS back box
Forge DV
ITG panel filter
If I am good to go I will need to buy metres to measure stats, I want to get hold of the Metres that Sit in that middle console up on the front dash(three metre's in a row), Where can I get them from? and Where canI get a dawes supplied and fitted?
Thanks
Ryan
P.S Sorry Alan for stepping in on your topic but this looks like a good place to put my question in.
09 March 2003, 01:27 PM
#73
Scooby Regular
Join Date: Dec 2002
Location: Sunny BELFAST
Posts: 19,408
Likes: 0
Received 0 Likes
on
0 Posts
SHUCK - northern ireland version of a ditch with or without a small stream running along it, or that 14 mile stretch of water that separates nothern ireland from scotland (larne-stranrar).
cheers
big sinky
cheers
big sinky
24 April 2003, 06:58 PM
#82
Scooby Regular
Join Date: Dec 2002
Location: Sunny BELFAST
Posts: 19,408
Likes: 0
Received 0 Likes
on
0 Posts
you still not got that motor of yours remapped yet. cmon m8 get the finger out i wanna see graphs and pie charts and figures etc. etc.
cheers
big sinky
cheers
big sinky
25 April 2003, 10:20 AM
#84
Scooby Regular
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
Alan, you and about 10 other people.. (and you werent the first!)
Get another ecu if you want.. it will cost you aprox. 16.9 times as much, not including petrol to get to wherever its fitted.
Like I said Im waiting for my supplier, theres not really much I can do is there?
Dont really give a **** if people dont believe me.
David
Get another ecu if you want.. it will cost you aprox. 16.9 times as much, not including petrol to get to wherever its fitted.
Like I said Im waiting for my supplier, theres not really much I can do is there?
Dont really give a **** if people dont believe me.
David
25 April 2003, 10:40 AM
#86
Alex?
27C1028s?
Some about?
There's a really easy way to cut those queues, raise the price by 50%.
I would just like to thank the people that have been patient, not bugged me, yet been happy when it's done.
Paul
27C1028s?
Some about?
There's a really easy way to cut those queues, raise the price by 50%.
I would just like to thank the people that have been patient, not bugged me, yet been happy when it's done.
Paul
25 April 2003, 11:34 AM
#88
Scooby Regular
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
Paul dont laugh.. but Im going to increase the price to £100.. it will save the stress..
Simon has just called and will have them tuesday.
Cheers Simon
David
Simon has just called and will have them tuesday.
Cheers Simon
David