If you have 4-Pot Brakes ....
#31
Scooby Regular
Thread Starter
Originally Posted by wrxtankie
The one thing I will add is if your not 100% certain, on any problems or exactly what your doing when brakes are concerened Then don't
Pete
#32
Scooby Regular
Join Date: Sep 2003
Location: No longer Japan !
Posts: 1,742
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by pslewis
I am an Engineer ..... I don't know how many wires are holding up the Severn Bridge either - good god I must be a really poor Engineer FFS
Pete
Pete
#33
Scooby Regular
Join Date: Oct 2005
Location: West London
Posts: 1,914
Likes: 0
Received 0 Likes
on
0 Posts
Pete, you can push the pistons back with some water pump pliers. Just wrap the jaws in tape to prevent damage to the surface of the caliper.
In your position i'd use Dot 4 fluid, Dot 3 is more likely to absorb moisture and need changing a bit more often.
Cracking the bleed nipple is an option but so long as you push the pistons back slowly you won't reverse any seals in the master cylinder.
I did mine this afternoon , changed for some EBC Red stuff. World of difference from standard and i'm quite light on my brakes.
Andy
In your position i'd use Dot 4 fluid, Dot 3 is more likely to absorb moisture and need changing a bit more often.
Cracking the bleed nipple is an option but so long as you push the pistons back slowly you won't reverse any seals in the master cylinder.
I did mine this afternoon , changed for some EBC Red stuff. World of difference from standard and i'm quite light on my brakes.
Andy
#34
Scooby Regular
Thread Starter
Originally Posted by Brit_in_Japan
How many pistons has a four pot caliper have, that was your question wasn't it? It's not rocket science, though you would be be happier if it was wouldn't you?
All I knew was I had 4-pot brakes .... now **** off!
Pete
#35
Scooby Regular
Thread Starter
Originally Posted by bugeyeandy
Pete, you can push the pistons back with some water pump pliers. Just wrap the jaws in tape to prevent damage to the surface of the caliper.
In your position i'd use Dot 4 fluid, Dot 3 is more likely to absorb moisture and need changing a bit more often.
Cracking the bleed nipple is an option but so long as you push the pistons back slowly you won't reverse any seals in the master cylinder.
I did mine this afternoon , changed for some EBC Red stuff. World of difference from standard and i'm quite light on my brakes.
Andy
In your position i'd use Dot 4 fluid, Dot 3 is more likely to absorb moisture and need changing a bit more often.
Cracking the bleed nipple is an option but so long as you push the pistons back slowly you won't reverse any seals in the master cylinder.
I did mine this afternoon , changed for some EBC Red stuff. World of difference from standard and i'm quite light on my brakes.
Andy
Pete
#39
Scooby Regular
Join Date: Oct 2001
Location: North Yorks, MY03 PPP, now run a Mondeo ST TDCI 06
Posts: 1,032
Likes: 0
Received 0 Likes
on
0 Posts
I've never used the cracked nipple technique, just take the brake fluid reservoir cap off and push the pistons back using water pump pliers or a large screwdriver.
If the nipple snaps off, you're in trouble then Pete......I'd be tempted to buy a new nipple if you intend to go this route. Stupid idea if you want my opinion!
If the nipple snaps off, you're in trouble then Pete......I'd be tempted to buy a new nipple if you intend to go this route. Stupid idea if you want my opinion!
#42
Scooby Regular
Thread Starter
Originally Posted by stockcar
Pete your car has the later style single piston sliding caliper with 266mm vented rear discs....................
alyn
alyn
Pete
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM