Had my car on the rollers
#33
Scooby Regular
iTrader: (3)
Join Date: Aug 2000
Location: 1600cc's of twin scroll fun :)
Posts: 25,565
Likes: 0
Received 2 Likes
on
2 Posts
Probably pushing no more that 20bhp above standard, so about 276bhp, not a chance of anything above that without a remap or chip in there, if it were running 320+bhp i would be getting a little scared, that poor engine will be killing itself!
Tony
Tony
#35
Scooby Regular
iTrader: (3)
Join Date: Aug 2000
Location: 1600cc's of twin scroll fun :)
Posts: 25,565
Likes: 0
Received 2 Likes
on
2 Posts
You wont make 65bhp with an exhaust and filter, 20 tops on that so either the rolling road is out (they do have to be calibrated ) or your car has a few other bits that are not quite standard (chipped).
Tony
Tony
#39
Scooby Regular
Thread Starter
iTrader: (4)
Join Date: Aug 2008
Location: Grimsby
Posts: 182
Likes: 0
Received 0 Likes
on
0 Posts
I always drive it with respect and never plant my foot, not all the time i want to get it set up with an apexi power fc.
This is my first rolling road i have done so dont no much about them, like a lot of you guys!
This is my first rolling road i have done so dont no much about them, like a lot of you guys!
#40
Scooby Regular
iTrader: (3)
Join Date: Aug 2000
Location: 1600cc's of twin scroll fun :)
Posts: 25,565
Likes: 0
Received 2 Likes
on
2 Posts
You can check to see if your ecu has been chipped (it wont make that power normally) by opening it up, or if you have a boost gauge these normally run about .9bar standard
Tony
Tony
#41
Scooby Regular
Join Date: Jan 2007
Location: south west
Posts: 437
Likes: 0
Received 0 Likes
on
0 Posts
very nice m8, its a fun bhp area to be, loving mine, i would recommend the simtec over the apexi, 2 stage boost, launch control, an anti-lag, witch can be a lot of fun in town scaring people i dont know what area u in but speak to dave at tileys of bristol,
#44
Scooby Regular
iTrader: (10)
Join Date: Jan 2008
Location: Bedfordshire
Posts: 3,071
Likes: 0
Received 0 Likes
on
0 Posts
Im running similar power, but look at my profile for mods!
Very good result.But, without a different ecu or boost controler, the car would hit fuel cut at 1.1 bar. The standard map sensor can't go above this, unless the pressure is beeing bled off. Look at your ecu, im curious now!
Very good result.But, without a different ecu or boost controler, the car would hit fuel cut at 1.1 bar. The standard map sensor can't go above this, unless the pressure is beeing bled off. Look at your ecu, im curious now!
#45
Former Sponsor
iTrader: (4)
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes
on
2 Posts
I expect it has a mines or zerosports ecu chip in it.. should be a sticker on the case.. they remove the boost cut and increase the boost duty.. with you then adding the mods it will have upped the boost further etc..
If iti s on original injectors which are grey and 380cc then be very careful (don't use boost) as they max out at 300bhp running the correct fuelling so I would assume it is very lean..
Or as said the dyno over read and it is perfectly fine but running less power.
Simon
If iti s on original injectors which are grey and 380cc then be very careful (don't use boost) as they max out at 300bhp running the correct fuelling so I would assume it is very lean..
Or as said the dyno over read and it is perfectly fine but running less power.
Simon
Thread
Thread Starter
Forum
Replies
Last Post
ossett2k2
Engine Management and ECU Remapping
15
23 September 2015 09:11 AM
Adam Kindness
ScoobyNet General
0
15 September 2015 03:31 PM