Breaking 2.5 Newage.... Goodies..
07 September 2009, 10:04 AM
#33
if not been asked for already and i know you are not spliting until you have sold the engine etc
but i would be after those front lights!!
best of luck with the rest though
cheers
steve
but i would be after those front lights!!
best of luck with the rest though
cheers
steve
07 September 2009, 05:43 PM
#35
Scooby Regular
Thread Starter
iTrader: (35)
Join Date: Nov 2006
Posts: 2,784
Likes: 0
Received 0 Likes
on
0 Posts
Steve, lights not for sale, going to be left in the car.
Harry, the clutch is def sold m8.
I am planning on putting a 2006 wrx 2.5 engine, 20G turbo, and 5 speed box in the car, along with brembo's and a STi interior.
Car will then be up for sale as a complete car, though for what price I'm not too sure as yet.
Neil.
Harry, the clutch is def sold m8.
I am planning on putting a 2006 wrx 2.5 engine, 20G turbo, and 5 speed box in the car, along with brembo's and a STi interior.
Car will then be up for sale as a complete car, though for what price I'm not too sure as yet.
Neil.
08 September 2009, 07:39 PM
#41
Scooby Regular
Thread Starter
iTrader: (35)
Join Date: Nov 2006
Posts: 2,784
Likes: 0
Received 0 Likes
on
0 Posts
Updated.
Engine spec
EJ 257 std engine cases
Lateral performance H section fast road rods
Lateral performance/wiseco hone to fit pistons
ACL bearings
ARP 11mm head studs
Triple layer head gaskets
STi5 heads, fully ported and polished, with re-profiled Piper cams (not sure on the spec, but seem to remember quite mild)
RCM oil pump
Centre breather blocked off.
Long motor was built by Zen with new Crank, modine, water pump etc, and has completed just under 10,000 trouble free miles.
£3300.00
MD 321 V turbo, with rotated compressor wheel (180 degrees) and 3" inlet, though I can convert back to std fitment if required. £1300.00
356mm front and rear brake set up.
These started out as a Ksport kit, which I had machined and anodised in blue.
Fronts are 8 pot, rears 6 pot. £1200.00
Oil cooler kit, with take off plate, and heavy duty long pipework, to allow the routing around the back of the engine, away from the exhaust manifold. £200.00
Whiteline Rear 22mm Anti roll bar £80.00
Whiteline Front 22mm Anti roll bar £80.00
Whiteline rear steel drop links £30.00
Whiteline rear strut brace 80.00
Heavy duty STi 6 speed gearbox mount, and engine mounts £70.00
Lateral Performance modified injectors, top feed, 800cc £250.00
Inlet manifold, fuel rails and parallel fuel lines,all in -6 fittings and braided lines ready to fit £300.00
JDM Defi style instrument cluster, complete with speedo converter £200.00
Recaro speed seats, runners, and rear bench trimmed to match, £1200.00
Flocked dashboard, complete upper and lower sections, glove box, with flocked clock surround, instrument surround and steering column £250.00
2005 on Flocked door cards 100.00
Flocked A, B and C pillars £100.00
Or can do a deal on all the flocked items if interested.
I am advertising on several forums, so to make everything fair can any interested parties e-mail me at neilrobinson05@aol.com
Engine spec
EJ 257 std engine cases
Lateral performance H section fast road rods
Lateral performance/wiseco hone to fit pistons
ACL bearings
ARP 11mm head studs
Triple layer head gaskets
STi5 heads, fully ported and polished, with re-profiled Piper cams (not sure on the spec, but seem to remember quite mild)
RCM oil pump
Centre breather blocked off.
Long motor was built by Zen with new Crank, modine, water pump etc, and has completed just under 10,000 trouble free miles.
£3300.00
MD 321 V turbo, with rotated compressor wheel (180 degrees) and 3" inlet, though I can convert back to std fitment if required. £1300.00
356mm front and rear brake set up.
These started out as a Ksport kit, which I had machined and anodised in blue.
Fronts are 8 pot, rears 6 pot. £1200.00
Oil cooler kit, with take off plate, and heavy duty long pipework, to allow the routing around the back of the engine, away from the exhaust manifold. £200.00
Whiteline Rear 22mm Anti roll bar £80.00
Whiteline Front 22mm Anti roll bar £80.00
Whiteline rear steel drop links £30.00
Whiteline rear strut brace 80.00
Heavy duty STi 6 speed gearbox mount, and engine mounts £70.00
Lateral Performance modified injectors, top feed, 800cc £250.00
Inlet manifold, fuel rails and parallel fuel lines,all in -6 fittings and braided lines ready to fit £300.00
JDM Defi style instrument cluster, complete with speedo converter £200.00
Recaro speed seats, runners, and rear bench trimmed to match, £1200.00
Flocked dashboard, complete upper and lower sections, glove box, with flocked clock surround, instrument surround and steering column £250.00
2005 on Flocked door cards 100.00
Flocked A, B and C pillars £100.00
Or can do a deal on all the flocked items if interested.
I am advertising on several forums, so to make everything fair can any interested parties e-mail me at neilrobinson05@aol.com
11 September 2009, 08:29 AM
#47
Scooby Regular
Thread Starter
iTrader: (35)
Join Date: Nov 2006
Posts: 2,784
Likes: 0
Received 0 Likes
on
0 Posts
Updated.
Engine spec
EJ 257 std engine cases
Lateral performance H section fast road rods
Lateral performance/wiseco hone to fit pistons
ACL bearings
ARP 11mm head studs
Triple layer head gaskets
STi5 heads, fully ported and polished, with re-profiled Piper cams (not sure on the spec, but seem to remember quite mild)
RCM oil pump
Centre breather blocked off.
Long motor was built by Zen with new Crank, modine, water pump etc, and has completed just under 10,000 trouble free miles.
£3300.00
MD 321 V turbo, with rotated compressor wheel (180 degrees) and 3" inlet, though I can convert back to std fitment if required. £1300.00
356mm front and rear brake set up.
These started out as a Ksport kit, which I had machined and anodised in blue.
Fronts are 8 pot, rears 6 pot. £1200.00
Oil cooler kit, with take off plate, and heavy duty long pipework, to allow the routing around the back of the engine, away from the exhaust manifold. £200.00
Whiteline Rear 22mm Anti roll bar £80.00
Whiteline Front 22mm Anti roll bar £80.00
Whiteline rear steel drop links £30.00
Whiteline rear strut brace 80.00
Heavy duty STi 6 speed gearbox mount, and engine mounts £70.00
Lateral Performance modified injectors, top feed, 800cc £250.00
Inlet manifold, fuel rails and parallel fuel lines,all in -6 fittings and braided lines ready to fit £300.00
JDM Defi style instrument cluster, complete with speedo converter £200.00
Recaro speed seats, runners, and rear bench trimmed to match, £1200.00
I am advertising on several forums, so to make everything fair can any interested parties e-mail me at neilrobinson05@aol.com
Engine spec
EJ 257 std engine cases
Lateral performance H section fast road rods
Lateral performance/wiseco hone to fit pistons
ACL bearings
ARP 11mm head studs
Triple layer head gaskets
STi5 heads, fully ported and polished, with re-profiled Piper cams (not sure on the spec, but seem to remember quite mild)
RCM oil pump
Centre breather blocked off.
Long motor was built by Zen with new Crank, modine, water pump etc, and has completed just under 10,000 trouble free miles.
£3300.00
MD 321 V turbo, with rotated compressor wheel (180 degrees) and 3" inlet, though I can convert back to std fitment if required. £1300.00
356mm front and rear brake set up.
These started out as a Ksport kit, which I had machined and anodised in blue.
Fronts are 8 pot, rears 6 pot. £1200.00
Oil cooler kit, with take off plate, and heavy duty long pipework, to allow the routing around the back of the engine, away from the exhaust manifold. £200.00
Whiteline Rear 22mm Anti roll bar £80.00
Whiteline Front 22mm Anti roll bar £80.00
Whiteline rear steel drop links £30.00
Whiteline rear strut brace 80.00
Heavy duty STi 6 speed gearbox mount, and engine mounts £70.00
Lateral Performance modified injectors, top feed, 800cc £250.00
Inlet manifold, fuel rails and parallel fuel lines,all in -6 fittings and braided lines ready to fit £300.00
JDM Defi style instrument cluster, complete with speedo converter £200.00
Recaro speed seats, runners, and rear bench trimmed to match, £1200.00
I am advertising on several forums, so to make everything fair can any interested parties e-mail me at neilrobinson05@aol.com
16 September 2009, 08:37 PM
#49
Scooby Regular
Thread Starter
iTrader: (35)
Join Date: Nov 2006
Posts: 2,784
Likes: 0
Received 0 Likes
on
0 Posts
Updated.
Engine spec
EJ 257 std engine cases
Lateral performance H section fast road rods
Lateral performance/wiseco hone to fit pistons
ACL bearings
ARP 11mm head studs
Triple layer head gaskets
STi5 heads, fully ported and polished, with re-profiled Piper cams (not sure on the spec, but seem to remember quite mild)
RCM oil pump
Centre breather blocked off.
Long motor was built by Zen with new Crank, modine, water pump etc, and has completed just under 10,000 trouble free miles.
Comes complete with cam pullies, belt and covers in tack ready to bolt in your car.
£3200.00
MD 321 V turbo, with rotated compressor wheel (180 degrees) and 3" inlet, though I can convert back to std fitment if required. £1300.00
356mm front and rear brake set up.
These started out as a Ksport kit, which I had machined and anodised in blue.
Fronts are 8 pot, rears 6 pot. £1000.00
Oil cooler kit, with take off plate, and heavy duty long pipework, to allow the routing around the back of the engine, away from the exhaust manifold. £160.00
Whiteline Rear 22mm Anti roll bar £75.00
Whiteline Front 22mm Anti roll bar £75.00
Whiteline rear steel drop links £30.00
Whiteline rear strut brace £70.00
Lateral Performance modified injectors, top feed, 800cc £220.00
Inlet manifold, fuel rails with -6 ends,parallel fuel lines and fuel lab fuel regulator,all in -6 fittings and braided lines ready to fit to your newage £350.00
JDM Defi style instrument cluster, complete with speedo converter £180.00
Recaro speed seats, runners, and rear bench trimmed to match, along with a set of 2005> matching door cards £1200.00
Harness bar, powder coated in black, c/w rose jointed supports £140.00
Carl Davey inlet manifold spacers £45.00
Carl Davey header tank insulators £10.00
Carbon fibre STi door step/sill plates. £120.00
I am advertising on several forums, so to make everything fair can any interested parties e-mail me at neilrobinson05@aol.com
Engine spec
EJ 257 std engine cases
Lateral performance H section fast road rods
Lateral performance/wiseco hone to fit pistons
ACL bearings
ARP 11mm head studs
Triple layer head gaskets
STi5 heads, fully ported and polished, with re-profiled Piper cams (not sure on the spec, but seem to remember quite mild)
RCM oil pump
Centre breather blocked off.
Long motor was built by Zen with new Crank, modine, water pump etc, and has completed just under 10,000 trouble free miles.
Comes complete with cam pullies, belt and covers in tack ready to bolt in your car.
£3200.00
MD 321 V turbo, with rotated compressor wheel (180 degrees) and 3" inlet, though I can convert back to std fitment if required. £1300.00
356mm front and rear brake set up.
These started out as a Ksport kit, which I had machined and anodised in blue.
Fronts are 8 pot, rears 6 pot. £1000.00
Oil cooler kit, with take off plate, and heavy duty long pipework, to allow the routing around the back of the engine, away from the exhaust manifold. £160.00
Whiteline Rear 22mm Anti roll bar £75.00
Whiteline Front 22mm Anti roll bar £75.00
Whiteline rear steel drop links £30.00
Whiteline rear strut brace £70.00
Lateral Performance modified injectors, top feed, 800cc £220.00
Inlet manifold, fuel rails with -6 ends,parallel fuel lines and fuel lab fuel regulator,all in -6 fittings and braided lines ready to fit to your newage £350.00
JDM Defi style instrument cluster, complete with speedo converter £180.00
Recaro speed seats, runners, and rear bench trimmed to match, along with a set of 2005> matching door cards £1200.00
Harness bar, powder coated in black, c/w rose jointed supports £140.00
Carl Davey inlet manifold spacers £45.00
Carl Davey header tank insulators £10.00
Carbon fibre STi door step/sill plates. £120.00
I am advertising on several forums, so to make everything fair can any interested parties e-mail me at neilrobinson05@aol.com
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
shorty87
Full Cars Breaking For Spares
19
22 December 2015 11:59 AM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
