dv help
03 September 2009, 12:12 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
did you cut out and join were the hole was for the dump valve in the ic pipe
03 September 2009, 12:16 PM
Scooby Senior
Join Date: Dec 2005
Location: Standing Up
Posts: 16,742
No mate on fitting mine was pre-welded incorporating the Simtek temp sensor, on yours you could use a clamped bit of samco with a pipe bung.
03 September 2009, 12:24 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
see mine dont make that sort of noise
03 September 2009, 12:36 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
that on you tube is that a vta cause mine sounds different
03 September 2009, 12:37 PM
Scooby Senior
Join Date: Dec 2005
Location: Standing Up
Posts: 16,742
03 September 2009, 12:37 PM
Scooby Regular
Join Date: Jan 2005
Location: Essex
Posts: 12,706
Likes: 0
Don't forget these guys are running no dump valve at all. If you run the recirc you'll get the woosh through the IK first then a small amount of chatter. By not having the recirc you'll get more pressure backing up against the turbo blades which will give a louder chatter (which is really turbo stall). Just blank off the vacum to the top of the vta dv to start with to see if it changes the amount of chatter you get.
03 September 2009, 12:40 PM
Scooby Senior
Join Date: Dec 2005
Location: Standing Up
Posts: 16,742
Big **** Roger Clarke K&N with 80mm RCM Cone
It sucks !
03 September 2009, 12:42 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
i get loads of chatter as it is its the noise before that ,that doesnt sound like anyone elses i get the noise then chatter i carnt explain it really
03 September 2009, 12:44 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
but aint all that pressure gona do some damage cause it has no were to go but back,also wouldnt that mess with the maf thus giving it wrong readings
03 September 2009, 12:46 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
ill be better with the recir valve then
03 September 2009, 12:47 PM
Scooby Senior
Join Date: Dec 2005
Location: Standing Up
Posts: 16,742
03 September 2009, 12:49 PM
Scooby Regular
Join Date: Jan 2005
Location: Essex
Posts: 12,706
Likes: 0
Quote:
Originally Posted by
53WRX
Big **** Roger Clarke K&N with 80mm RCM Cone
It sucks !
03 September 2009, 12:50 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
ill be needing a recir valve then
03 September 2009, 01:39 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
were can i get one from and how much
03 September 2009, 01:44 PM
Scooby Regular
Join Date: Jan 2005
Location: Essex
Posts: 12,706
Likes: 0
how much do you want for your vta?
03 September 2009, 02:32 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
dont even know how much its worth how much for your recir valve or some sort of deal
03 September 2009, 02:49 PM
Scooby Regular
Join Date: Jan 2005
Location: Essex
Posts: 12,706
Likes: 0
Can get a new vta dv for about £35 from ebay, and tbh you can get aftermarket recirc dv for about £30 on there, better bet than a standard one imo. should be a little more responsive. Guess a standard dv would cost about £15 from a breakers so call it £10. Up to you.
03 September 2009, 03:06 PM
Scooby Regular
Thread Starter
Join Date: Feb 2007
Posts: 245
Likes: 0
Received 0 Likes
on
0 Posts
do i need extra pipes to fit this ie going to the air intake,so what sort of deal u looking for will have to change at the same time i guess
03 September 2009, 12:37 PM
