TransPlanting an STi3/4 Engine Into Uk Scoob
#1
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Apr 2002
Posts: 2,808
Likes: 0
Received 0 Likes
on
0 Posts
TransPlanting an STi3/4 Engine Into Uk Scoob
As above shoe horned into a 94 UK, I have been led to believe that all sensors connectors Etc are the same & it is just Unplug , Plug back in.
Has anyone done this ??
What pitfalls did you fall into !! Etc
Thanks
Dean
Has anyone done this ??
What pitfalls did you fall into !! Etc
Thanks
Dean
#6
Scooby Regular
Join Date: Jan 2001
Location: Down South to Ooop North to Back Down South again!!
Posts: 6,633
Likes: 0
Received 0 Likes
on
0 Posts
Are you just changing the block or the whole engine? I've got am STI4 block in my MY95 UK & everythings a straight swap Obviously gaskets etc... all need replacing but that's about it.
MAFFA
MAFFA
#7
Scooby Regular
iTrader: (2)
Join Date: May 2000
Location: Class record holder at Pembrey Llandow Goodwood MIRA Hethel Blyton Curborough Lydden and Snetterton
Posts: 8,626
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Tim W
One thing you'll have to swap around is the throttle position sensor as that changed between phase 1 (to MY97) and 1.5 (from MY97 to MY99)
Trending Topics
#8
Scooby Regular
Join Date: Mar 2002
Location: Fcon Power Writer
Posts: 4,338
Likes: 0
Received 0 Likes
on
0 Posts
The ver3/4 loom is slightly different (hence the 3rd engine loom connector).
If you are just using the engine without the inlet manifold, your manifold will bolt straight on with your old loom.
If you want to use the ver3/4manifold then remove the ver 3/4loom and replace it with the ver 1/2 loom and adjust the TPS wiring as Tim said.
Basically the confusion comes as the early cars have 4 coil on plugs, whereas the ver 3/4 has a dual coil pack system using wasted spark.
Rob
If you are just using the engine without the inlet manifold, your manifold will bolt straight on with your old loom.
If you want to use the ver3/4manifold then remove the ver 3/4loom and replace it with the ver 1/2 loom and adjust the TPS wiring as Tim said.
Basically the confusion comes as the early cars have 4 coil on plugs, whereas the ver 3/4 has a dual coil pack system using wasted spark.
Rob
#9
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Apr 2002
Posts: 2,808
Likes: 0
Received 0 Likes
on
0 Posts
Cheers All,
Was planning on the whole Engine, CAr already has an Apexi Pfc Ecu, so would be remapping this afterwards, Whilst the engines are out i would just swap the Inlet manifold then.
Dean
Was planning on the whole Engine, CAr already has an Apexi Pfc Ecu, so would be remapping this afterwards, Whilst the engines are out i would just swap the Inlet manifold then.
Dean
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Sam Witwicky
Engine Management and ECU Remapping
17
13 November 2015 10:49 AM
Brzoza
Engine Management and ECU Remapping
1
02 October 2015 05:26 PM