Controlling DCCD, 6MT Classic
#1
Scooby Regular
Thread Starter
Join Date: Dec 2001
Location: Finland
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Controlling DCCD, 6MT Classic
The 6MT is mounted and working in my classic MY98, so next would be to take control of the DCCD.
One option would obviously be the Neetronics DCCD controller, like e.g. hmhaga has, but shouldn't it be possible to control the DCCD just by feeding power to it, and vary the voltage using the C-diff roller switch ?
At least that's what I have understood, that the roller switch varies the output, but is it between 0-5 volts, or maybe between 0-3 ? Anyway, the big question is, should the switch be fed with something lower than 12 V, does any one KNOW for sure?
I have switches like these two available, but I guess I won't have any use for the second one in a setup like this.
One option would obviously be the Neetronics DCCD controller, like e.g. hmhaga has, but shouldn't it be possible to control the DCCD just by feeding power to it, and vary the voltage using the C-diff roller switch ?
At least that's what I have understood, that the roller switch varies the output, but is it between 0-5 volts, or maybe between 0-3 ? Anyway, the big question is, should the switch be fed with something lower than 12 V, does any one KNOW for sure?
I have switches like these two available, but I guess I won't have any use for the second one in a setup like this.
Last edited by Miki; 03 January 2006 at 05:25 PM.
#2
Scooby Regular
Thread Starter
Join Date: Dec 2001
Location: Finland
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Ok, having read for example this old thread...
http://forums.nasioc.com/forums/showthread.php?t=534379
... I guess it's not as easy I was hoping for.
Any comments guys !?
http://forums.nasioc.com/forums/showthread.php?t=534379
... I guess it's not as easy I was hoping for.
Any comments guys !?
#3
This has some information about the controller...
http://forums.nasioc.com/forums/show...=dccd+software
http://forums.nasioc.com/forums/show...=dccd+software
#4
Scooby Regular
Thread Starter
Join Date: Dec 2001
Location: Finland
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Should have asked "back home" first maybe.... thanks malinen!
I've been doing some DCCD reading today, and apparently there are some options out there, just need to decide on how much I want to spend (more money? No, not again!!!!).
One thing is for sure, my rear diff will most probably be a vvvvery weak point in this setup.
I've been doing some DCCD reading today, and apparently there are some options out there, just need to decide on how much I want to spend (more money? No, not again!!!!).
One thing is for sure, my rear diff will most probably be a vvvvery weak point in this setup.
#7
Scooby Regular
Thread Starter
Join Date: Dec 2001
Location: Finland
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Damn it, my mapping/dyno session today was ruined due to lack of a DCCD controller.
It was not possible to drive the car on the dyno with the DCCD completely unlocked, at WOT it was ok, but when lifting the throttle it sounded like the the front diff (or something...) was about to explode.
Need to get the controller asap, so I can get my car tuned!
It was not possible to drive the car on the dyno with the DCCD completely unlocked, at WOT it was ok, but when lifting the throttle it sounded like the the front diff (or something...) was about to explode.
Need to get the controller asap, so I can get my car tuned!
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
supshon
General Technical
2
03 October 2015 08:06 PM