Ok so the 20G, SX & 740's are on... help!
#1
Scooby Regular
Thread Starter
![Unhappy](https://www.scoobynet.com/images/icons/icon9.gif)
Just back in... s0dding cold... fitted the 20G, SX Fuel Reg & Nismo 740's.... guess what... turned over and did not fully catch...... now just turns ... Andy F mapping the car tomorrow and fitting a PFC.... alas I cannae start the s0dding thing to get to him.... just hope it's just flooded and will dry out by the morning... any suggestions..?
Set the SX @ 2bar for starts... b0llox...
Will the stock ECU run with the 740's set @ 2bar? ...
Hoping there are some of you on the late shift logging in to help... lol..
Set the SX @ 2bar for starts... b0llox...
Will the stock ECU run with the 740's set @ 2bar? ...
Hoping there are some of you on the late shift logging in to help... lol..
![Frown](https://www.scoobynet.com/images/smilies/frown.gif)
#5
Scooby Regular
Thread Starter
![Default](https://www.scoobynet.com/images/icons/icon1.gif)
Originally Posted by Jolly Green Monster
refit original injectors, leave early and drive there and then swap them?
Simon
Simon
Trimmed the required material from the newer style 740's as required, slotted straight in.. fuel reg set @ 2bar. The stock system runs @ 3bar? Anything else to check before pulling the injectors? Kicking off with Andy in 2 hours... looking grim
![Frown](https://www.scoobynet.com/images/smilies/frown.gif)
#6
Former Sponsor
iTrader: (4)
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes
on
2 Posts
![Default](https://www.scoobynet.com/images/icons/icon1.gif)
the injectors will need a certain pressure to create a usable spray pattern.. it is a bit cowboy but try a slightly higher pressure and see if it runs..
if still not then you must have missed something somewhere?
Simon
if still not then you must have missed something somewhere?
Simon
#7
Scooby Regular
Thread Starter
![Default](https://www.scoobynet.com/images/icons/icon1.gif)
Originally Posted by Jolly Green Monster
the injectors will need a certain pressure to create a usable spray pattern.. it is a bit cowboy but try a slightly higher pressure and see if it runs..
if still not then you must have missed something somewhere?
Simon
if still not then you must have missed something somewhere?
Simon
Other than that.. just back... a tank of Optimax... and a huge grin... top bloke, car transformed into a road weapon... Cheers Andy.
![Big Grin](https://www.scoobynet.com/images/smilies/biggrin.gif)
Trending Topics
#8
Scooby Regular
Join Date: Jan 2005
Location: Braintree - 321BHP, 285Lbft-Perfect Standard' Ish STi Ver. III
Posts: 1,162
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://www.scoobynet.com/images/icons/icon1.gif)
Good to see you got your setup done and finished! Must be Lethal!
Are you hoping for 380+ on the rollers?
Stiver3
Are you hoping for 380+ on the rollers?
Stiver3
#9
Scooby Regular
Thread Starter
![Default](https://www.scoobynet.com/images/icons/icon1.gif)
Originally Posted by Stiver3
Good to see you got your setup done and finished! Must be Lethal!
Are you hoping for 380+ on the rollers?
Stiver3
Are you hoping for 380+ on the rollers?
Stiver3
![Smile](https://www.scoobynet.com/images/smilies/smile.gif)
Thread
Thread Starter
Forum
Replies
Last Post
Scott@ScoobySpares
Full Cars Breaking For Spares
61
11 January 2021 03:08 PM