Technical Help needed please
#1
Technical Help needed please
Hi all,
I have been driving my Scoob for a few months now with no worries. I drove to work this morning and all was fine. When I started the car up before the trip home the check engine light didnt go off. I had to get the car home so I drove it anyway, when accelerating within the boost range the car kind of stuttered. When driving without pushing the turbo though it seemed pretty normal. I wont beable to get the car to a garage until next week, anybody have any ideas as to what could be wrong?
Cheers
AK
I have been driving my Scoob for a few months now with no worries. I drove to work this morning and all was fine. When I started the car up before the trip home the check engine light didnt go off. I had to get the car home so I drove it anyway, when accelerating within the boost range the car kind of stuttered. When driving without pushing the turbo though it seemed pretty normal. I wont beable to get the car to a garage until next week, anybody have any ideas as to what could be wrong?
Cheers
AK
#2
Former Sponsor
iTrader: (4)
Joined: Jan 2001
Posts: 16,548
Likes: 2
From: ECU Mapping - www.JollyGreenMonster.co.uk
You need to read what the error code is that is now logged
ECU Reset and Error codes
Turn OFF the ignition
Connect Error code Connectors and Test Mode Connectors :
2 black connectors under dash, connect black to black and 2 green connectors under dash, connect green to green, they are by your left knee when sat in the drivers seat and often taped back to the loom if they haven't been used before.
Turn ON ignition but don't start the engine
Engine Check lamp comes on
Press accelerator pedal to the floor
Then return it to the half-throttle position and hold it there for two seconds
Release foot off the pedal completely
Start the engine
Check engine light error code is indicated by Pulsing lamp
If an error is detected then Check the ECU Code
If no error is detected - drive the car sensible for a couple of minutes
i.e. until warm (do not use boost or high rpm!)
When the ECU has been reset the Check Engine Light will flash
An Error Code is indicated by a flashing check engine light
of varying length of flash,
a flash of around once a second is the okay code and indicates all is well.
If an error code is detected Check the ECU Code
Turn ignition OFF and Disconnect Connectors
If there is a fault Check the Appropriate Sensor
Error Codes
An Error code is defined as a slow flash followed by fast flash
i.e 2 slow and 3 fast = 23 Mass Airflow sensor.
A continuous on/off at the same speed is no fault found.
Code Fault
11 Crankshaft position sensor
12 Starter switch
13 Camshaft position sensor
21 Engine coolant temperature sensor
22 Knock sensor
23 Mass air flow sensor
24 Idle air control solenoid
31 Throttle position sensor
32 Oxygen sensor
33 Vehicle speed sensor 2
35 Purge control solenoid valve
42 Idle switch
44 Wastegate control solenoid valve
45 Pressure sensor / Pressure exchange solenoid valve
51 Neutral position switch
ECU Reset and Error codes
Turn OFF the ignition
Connect Error code Connectors and Test Mode Connectors :
2 black connectors under dash, connect black to black and 2 green connectors under dash, connect green to green, they are by your left knee when sat in the drivers seat and often taped back to the loom if they haven't been used before.
Turn ON ignition but don't start the engine
Engine Check lamp comes on
Press accelerator pedal to the floor
Then return it to the half-throttle position and hold it there for two seconds
Release foot off the pedal completely
Start the engine
Check engine light error code is indicated by Pulsing lamp
If an error is detected then Check the ECU Code
If no error is detected - drive the car sensible for a couple of minutes
i.e. until warm (do not use boost or high rpm!)
When the ECU has been reset the Check Engine Light will flash
An Error Code is indicated by a flashing check engine light
of varying length of flash,
a flash of around once a second is the okay code and indicates all is well.
If an error code is detected Check the ECU Code
Turn ignition OFF and Disconnect Connectors
If there is a fault Check the Appropriate Sensor
Error Codes
An Error code is defined as a slow flash followed by fast flash
i.e 2 slow and 3 fast = 23 Mass Airflow sensor.
A continuous on/off at the same speed is no fault found.
Code Fault
11 Crankshaft position sensor
12 Starter switch
13 Camshaft position sensor
21 Engine coolant temperature sensor
22 Knock sensor
23 Mass air flow sensor
24 Idle air control solenoid
31 Throttle position sensor
32 Oxygen sensor
33 Vehicle speed sensor 2
35 Purge control solenoid valve
42 Idle switch
44 Wastegate control solenoid valve
45 Pressure sensor / Pressure exchange solenoid valve
51 Neutral position switch
Thread
Thread Starter
Forum
Replies
Last Post
robbie1988
Wanted
2
13 September 2015 10:25 AM
Scooby-Doo 2
Wheels And Tyres For Sale
1
09 September 2015 07:51 PM