TD05 18G ?
#1
TD05 18G ?
Hi guys,
thinking of buying a td05 18g turbo second hand supplied by Zen performance, my original plans were to get a andy forest or a blouch one , is the zen performance 18g similar i was hoping to achieve 370bhp onn my p1 with supporting mods....just i heeard some turbos dont perform well and wasnt to familiar with zen...
cheers
thinking of buying a td05 18g turbo second hand supplied by Zen performance, my original plans were to get a andy forest or a blouch one , is the zen performance 18g similar i was hoping to achieve 370bhp onn my p1 with supporting mods....just i heeard some turbos dont perform well and wasnt to familiar with zen...
cheers
#2
Scooby Regular
iTrader: (23)
Join Date: Jul 2008
Location: In the fast lane
Posts: 3,458
Likes: 0
Received 0 Likes
on
0 Posts
Hi, I have an 18g on my '05 STi supplied, fitted, and mapped by Zen.
No two engine builds are the same so it won't necessarily follow that your results will be the same as mine.
I am running a hyperflow tmic, 255 fuel pump, full decat, RCM intake, 10% bio ethanol and it made 363/358.
From what I've read you might hit 370, you might only make 350, but that will be nothing to do with where you buy the turbo.
However there's more to the story than just numbers.
The 18g spools quicker than the VF35 and hits 1 bar 1000rpm sooner. Nice low down torque and more sustained grunt at the top end.
It's a good mild tweak for a fast road car, and in a lighter car such as a P1 should be very nice to drive.
One thing I will say is that Paul will get the most out of the engine without risking it breaking.
Hope this helps.
No two engine builds are the same so it won't necessarily follow that your results will be the same as mine.
I am running a hyperflow tmic, 255 fuel pump, full decat, RCM intake, 10% bio ethanol and it made 363/358.
From what I've read you might hit 370, you might only make 350, but that will be nothing to do with where you buy the turbo.
However there's more to the story than just numbers.
The 18g spools quicker than the VF35 and hits 1 bar 1000rpm sooner. Nice low down torque and more sustained grunt at the top end.
It's a good mild tweak for a fast road car, and in a lighter car such as a P1 should be very nice to drive.
One thing I will say is that Paul will get the most out of the engine without risking it breaking.
Hope this helps.
#4
Scooby Regular
iTrader: (13)
18g rated upto 375 or thereabouts (earlier spool)
20g rated upto 400 or thereabouts (later spool)
As said above, you can't guarantee a bhp/lb ft figure for any given supp mods/remap/fuel mapped... but it helps you choose the correct turbo for what you want to try to achieve, etc...
20g rated upto 400 or thereabouts (later spool)
As said above, you can't guarantee a bhp/lb ft figure for any given supp mods/remap/fuel mapped... but it helps you choose the correct turbo for what you want to try to achieve, etc...
Trending Topics
#10
Scooby Regular
iTrader: (12)
Join Date: Jun 2009
Location: Essex
Posts: 780
Likes: 0
Received 0 Likes
on
0 Posts
I just changed the turbo on my car as it was leaking oil on the return and some fins were bent! (I don't know how but it was like that when I removed it)
Now it just doesn't seem as quick or as loud
They are both TD05's but how do I tell if it's 16g, 18g or 20g?? and would it make a difference to how my car sounded???
Now it just doesn't seem as quick or as loud
They are both TD05's but how do I tell if it's 16g, 18g or 20g?? and would it make a difference to how my car sounded???
#11
Scooby Regular
iTrader: (13)
Where/who did you get the turbo from? Is it 2nd hand, etc, etc? You sure you refitted the up-pipe//intake pipe/IC pipe/downpipe/all gaskets, all correctly?
If you have fitted an 18g or 20g it needs to be remapped to make SAFE!!! and get the best out of it! If it is either of these turbos, then that's prob the reason why it feels different - must get it remapped to optimise it. Don't drive on boost and try not to drive much at all until you get it mapped!!! Also you might have too small injectors, etc, etc...
What MY is yours? Is it a MY93-96? Has the turbo got the upturned 90deg 'snorkel' for the intake pipe, etc, etc? If so it'll almost certainly be a MY93-96 TD05H 16g... or possibly the smaller TD04L!
An OEM TD05H or TD04L will have the OEM embossed serial codes embossed on the bottom of the comp cover... Amongst other writing, at the very bottom it should read "TD05H..." (or "TD04L...") - you should be able to see it looking down in the gap by the intake pipe...
If you have fitted an 18g or 20g it needs to be remapped to make SAFE!!! and get the best out of it! If it is either of these turbos, then that's prob the reason why it feels different - must get it remapped to optimise it. Don't drive on boost and try not to drive much at all until you get it mapped!!! Also you might have too small injectors, etc, etc...
What MY is yours? Is it a MY93-96? Has the turbo got the upturned 90deg 'snorkel' for the intake pipe, etc, etc? If so it'll almost certainly be a MY93-96 TD05H 16g... or possibly the smaller TD04L!
An OEM TD05H or TD04L will have the OEM embossed serial codes embossed on the bottom of the comp cover... Amongst other writing, at the very bottom it should read "TD05H..." (or "TD04L...") - you should be able to see it looking down in the gap by the intake pipe...
Last edited by joz8968; 22 September 2009 at 05:11 PM.
#14
Scooby Regular
iTrader: (13)
lol It won't say "OEM"! OEM stands for original equipment manufacturers. It just means it's a std Subaru turbo... BUT...
What MY car do you have? It looks like a STi v.5/6 Wagon in your avatar??? If so, normally these would be fitted with a front entry IHI VF28 as std.! (So a previous owner must've changed it for a TD05!)
Is your TD05H therefore a front entry one? Was the old turbo physically the same size as this replacement? If so, then yeah, it's invariably either an aftermarket TD05 16g with a front entry cover to it, or an early OEM MY93-96 one converted to front entry by means of a new front-entry cover... or still has the OEM cover but with the snorkel chopped off...
Any chance of a pic trying to show the size/shape of the 'snail' and that writing on the cover?
What MY car do you have? It looks like a STi v.5/6 Wagon in your avatar??? If so, normally these would be fitted with a front entry IHI VF28 as std.! (So a previous owner must've changed it for a TD05!)
Is your TD05H therefore a front entry one? Was the old turbo physically the same size as this replacement? If so, then yeah, it's invariably either an aftermarket TD05 16g with a front entry cover to it, or an early OEM MY93-96 one converted to front entry by means of a new front-entry cover... or still has the OEM cover but with the snorkel chopped off...
Any chance of a pic trying to show the size/shape of the 'snail' and that writing on the cover?
Last edited by joz8968; 22 September 2009 at 05:27 PM.
#18
Scooby Regular
iTrader: (12)
Join Date: Jun 2009
Location: Essex
Posts: 780
Likes: 0
Received 0 Likes
on
0 Posts
It was off a car that was breaking but the turbo had only been on the car for 12 months.
It works fine it's just that I put a replacement engine in mine and changed the turbo but it doesn't seen as mentaly fast as before or sound as loud!!!
I'm just hoping that the engine I put in was an sti unit and not a wrx only! It cam out of an sti but you never know!
Rolling road I think is my next move.
It works fine it's just that I put a replacement engine in mine and changed the turbo but it doesn't seen as mentaly fast as before or sound as loud!!!
I'm just hoping that the engine I put in was an sti unit and not a wrx only! It cam out of an sti but you never know!
Rolling road I think is my next move.
#19
Scooby Regular
iTrader: (13)
Well at least you've got the correct turbo for your MY of car etc. - that's that question squared away.
The most obvious thing for it not feeling as spritely, is that it could be making less boost (for whatever reason). Obviously, if healthy, it should perform the same as the previous, same TD05H turbo (as the ECU controls the boost upto a max programmmed pressure level)... But perhaps there is an issue with it!(?)...
Do you have a mate who has a mechanical boost gauge that you could temp. hook up, just to make sure this replacement turbo is making the correct boost target for your car variant? When you establish that first, then you can go from there...
I think the STi v.2 Wagon's boost target is around 13psi (0.9bar) and boost cut happens at 16psi (1.1bar).
The most obvious thing for it not feeling as spritely, is that it could be making less boost (for whatever reason). Obviously, if healthy, it should perform the same as the previous, same TD05H turbo (as the ECU controls the boost upto a max programmmed pressure level)... But perhaps there is an issue with it!(?)...
Do you have a mate who has a mechanical boost gauge that you could temp. hook up, just to make sure this replacement turbo is making the correct boost target for your car variant? When you establish that first, then you can go from there...
I think the STi v.2 Wagon's boost target is around 13psi (0.9bar) and boost cut happens at 16psi (1.1bar).
Last edited by joz8968; 22 September 2009 at 07:37 PM.
#20
Scooby Regular
iTrader: (12)
Join Date: Jun 2009
Location: Essex
Posts: 780
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for that.
Those settings look about what it was at before so I'll check em when I get out in her next.
I will be getting it mapped at sonme point so this can be sorted then yeah?
Jolly green monster the best option?
Those settings look about what it was at before so I'll check em when I get out in her next.
I will be getting it mapped at sonme point so this can be sorted then yeah?
Jolly green monster the best option?
#21
Scooby Regular
iTrader: (13)
Yep JGM for the win - I had my Apexi PFC mapped by Simon.
Yeah, unless something terminal with the actual turbo, Simon gives a brief "heathcheck" of the BCS system and replaces any split/perished vac lines with new hose, etc., before commencing mapping.
Any futher issues will no doubt become obvious and 'flag up' when the mapping is embarked upon...
Yeah, unless something terminal with the actual turbo, Simon gives a brief "heathcheck" of the BCS system and replaces any split/perished vac lines with new hose, etc., before commencing mapping.
Any futher issues will no doubt become obvious and 'flag up' when the mapping is embarked upon...
#22
Scooby Regular
iTrader: (12)
Join Date: Jun 2009
Location: Essex
Posts: 780
Likes: 0
Received 0 Likes
on
0 Posts
Just been and ragged the butt off it and all seems pretty ok now! maybe I was just expecting something bad?
I couldn't see my boost gauge as it's dark but I'm replacing my vac pipes as they are not to pretty.
I couldn't see my boost gauge as it's dark but I'm replacing my vac pipes as they are not to pretty.
#24
Scooby Regular
iTrader: (12)
Join Date: Jun 2009
Location: Essex
Posts: 780
Likes: 0
Received 0 Likes
on
0 Posts
Well it's dead now!!!!!!!!!
Was cruising up the motorway at 120 and it just lost loads of power and then loads of smoke came out the back!! Limped it home and checked under the bonnet and oil is everywhere! Dip stick is bone dry so I guess it's pretty dead now as I drove 15 miles like that
Back to the garage again
I'm about to get a Lada as they're more reliable!!
Was cruising up the motorway at 120 and it just lost loads of power and then loads of smoke came out the back!! Limped it home and checked under the bonnet and oil is everywhere! Dip stick is bone dry so I guess it's pretty dead now as I drove 15 miles like that
Back to the garage again
I'm about to get a Lada as they're more reliable!!
#25
Don't lose hope yet. It's just your turbo that's dead. A dry dipstick does not mean a completely empty sump, your engine is most probably still fine unless you can hear a rattling from the bottom end.
The dead turbo might make some sound, don't mistake it for a dead engine. The turbo sounds more like a scraping noise while engine bottom end noises are knocking sounds.
The dead turbo might make some sound, don't mistake it for a dead engine. The turbo sounds more like a scraping noise while engine bottom end noises are knocking sounds.
#26
Scooby Regular
iTrader: (13)
Yep, most probably the replacement turbo was shagged e.g. to much movement to the shaft, etc.
Whip your intake pipe off - is it very oily inside (rather than the normal thin film residue)? Also, now grab the shaft's nose and wiggle side to side and up and down - chances are it'll be moving around rather a lot (hope so). Also remove the IC pipe - has it got loads of oil in it (rather than a thin oil film again)? If so, remove the IC itself and angle its entry port down into a waste oil disposal barrel - does loads of oil drip out of it?!
If any of the above happens, 90% sure the turbo has failed.
BTW, when the car let go, was the plume of smoke white-blue in colour? If so, another sure sign of turbo failure.
Whip your intake pipe off - is it very oily inside (rather than the normal thin film residue)? Also, now grab the shaft's nose and wiggle side to side and up and down - chances are it'll be moving around rather a lot (hope so). Also remove the IC pipe - has it got loads of oil in it (rather than a thin oil film again)? If so, remove the IC itself and angle its entry port down into a waste oil disposal barrel - does loads of oil drip out of it?!
If any of the above happens, 90% sure the turbo has failed.
BTW, when the car let go, was the plume of smoke white-blue in colour? If so, another sure sign of turbo failure.
Last edited by joz8968; 23 September 2009 at 11:43 AM.
#28
Scooby Regular
iTrader: (12)
Join Date: Jun 2009
Location: Essex
Posts: 780
Likes: 0
Received 0 Likes
on
0 Posts
Ok update..
Just spoke to the mechanic and he started the car and said it's not running on all 4 cylinders and there is smoke coming from the exhaust but he needs to do a compression test 1st before he looks in to the turbo.
Just spoke to the mechanic and he started the car and said it's not running on all 4 cylinders and there is smoke coming from the exhaust but he needs to do a compression test 1st before he looks in to the turbo.
#29
Scooby Regular
iTrader: (13)
Yeah, even though theoretically the motor should still run, when a turbo catastrophically fails then sometimes the motor won't run. Could be due to compression or whatever, because now the non-working turbo has simply become just a big restriction in the intake system.
I'd defo get him to do those tests I mentioned - it might just be obvious that the turbo's failed, therefore saving everyone's time and, importantly, your labour costs!
I'd defo get him to do those tests I mentioned - it might just be obvious that the turbo's failed, therefore saving everyone's time and, importantly, your labour costs!
Last edited by joz8968; 23 September 2009 at 02:20 PM.