UK classic - turn off alarm chirp?
#1
Scooby Newbie
Thread Starter
UK classic - turn off alarm chirp?
I've got a uk classic with standard factory fit alarm, is there a way to turn off the arm and disarm chirps? I'm not really enjoying the stupid noises and don't think neighbous do either...
#2
Hi, Someone on here sent me a list of features the alarm has, If you put the ignition on, Press the remote button once, Press number 6 on the keypad and immediately turn off the ignition and it should work, It worked on my classic first time when I did it.
Hope this works for you.
Hope this works for you.
#5
Scooby Newbie
Thread Starter
do you know what Sigma model the alarm is on these - I think is Sigma M30?
Right, done a bit more searching (http://www.scouk.net/subaru-impreza/..._m30_codes.pdf) for Sigma M30 stuff and indeed "6" is the bleeps. So how do I enter it in? Do i just press 6 or do I need to enter in all this "* 17856 * ? #" whatnot code?
Right, done a bit more searching (http://www.scouk.net/subaru-impreza/..._m30_codes.pdf) for Sigma M30 stuff and indeed "6" is the bleeps. So how do I enter it in? Do i just press 6 or do I need to enter in all this "* 17856 * ? #" whatnot code?
#7
Scooby Newbie
Thread Starter
Trending Topics
#10
Scooby Newbie
Thread Starter
Number 7 I think:
User Features
The following features are switchable by the end user, using the keypad, and are detailed in the back of your operating instructions.
To access this mode - turn on the vehicle ignition, press the remote button once, type one of the numbers listed in the chart below, immediately turn off the ignition. The numbers will have the following effect:
Number Function
0 Last trigger isolation - allows the system to be set excluding any circuit giving a trigger signal
at the end of the settle time (i.e. allows the system to be set with a defective bonnet switch,
without “false alarming” until the switch can be replaced)
1 Turns off the bleeps only for the next time the system is armed (If bleeps turned on!)
2 Turn off ultrasonics only for the next time the system is armed (also possible by pressing the
Remote Key with the ignition on before arming)
3 Puts the system into valet mode (effectively freezing the passive immobilisation and any
other features such as auto arm when the vehicle goes in for service. System re-activated by
arming with the remote key).
4 Turn on auto-lock (an anti-hijack feature that locks the doors and boot when the ignition is
turned on)
5 Turn off auto-lock
6 Turn off bleeps every time system is armed or disarmed
(Turned off at manufacture to comply with legislation)
7 Turn on bleeps every time system is armed or disarmed
( Note: This will contravene current legislation)
8 Displays vehicle’s battery voltage – 10 flashes on dashboard LED = approximately 10 volts
9 Turn on super-lock for next set period (allows the alarm to arm, but then shuts down the
receiver. This reduces the systems current consumption if the vehicle is left for a number of
weeks. The system then can only be disarmed using your PIN number , this gives protection
even if your keys are stolen, whilst you are away on holiday.
* Toggles between loud and soft arming/disarming bleeps if selected ( See above note in 7)
The following features are switchable by the end user, using the keypad, and are detailed in the back of your operating instructions.
To access this mode - turn on the vehicle ignition, press the remote button once, type one of the numbers listed in the chart below, immediately turn off the ignition. The numbers will have the following effect:
Number Function
0 Last trigger isolation - allows the system to be set excluding any circuit giving a trigger signal
at the end of the settle time (i.e. allows the system to be set with a defective bonnet switch,
without “false alarming” until the switch can be replaced)
1 Turns off the bleeps only for the next time the system is armed (If bleeps turned on!)
2 Turn off ultrasonics only for the next time the system is armed (also possible by pressing the
Remote Key with the ignition on before arming)
3 Puts the system into valet mode (effectively freezing the passive immobilisation and any
other features such as auto arm when the vehicle goes in for service. System re-activated by
arming with the remote key).
4 Turn on auto-lock (an anti-hijack feature that locks the doors and boot when the ignition is
turned on)
5 Turn off auto-lock
6 Turn off bleeps every time system is armed or disarmed
(Turned off at manufacture to comply with legislation)
7 Turn on bleeps every time system is armed or disarmed
( Note: This will contravene current legislation)
8 Displays vehicle’s battery voltage – 10 flashes on dashboard LED = approximately 10 volts
9 Turn on super-lock for next set period (allows the alarm to arm, but then shuts down the
receiver. This reduces the systems current consumption if the vehicle is left for a number of
weeks. The system then can only be disarmed using your PIN number , this gives protection
even if your keys are stolen, whilst you are away on holiday.
* Toggles between loud and soft arming/disarming bleeps if selected ( See above note in 7)
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM