I need some tecnical help please.
27 September 2002 | 05:30 AM
#1
Thread Starter
Scooby Newbie
Joined: Sep 2002
Posts: 4
Likes: 0
a couple weeks ago i picked up a set of STIhead lights from germany i live in florida, anyways.. i made the lights work fine the only thing i have problems with is the leveler motor.
yes i got the switch too . the one with 4 pins on the back
now i know 2 of those pins are for the little light inside the switch the other 2 are a signal in and signal out with a diferent voltage, so far i know that the system works on (-)ground
now on the headlight motor it has 6 pins : pin 5 and 6 are power (12v)red wire and pin 6 ground(-)black wire
and there is 4 more wires a blue,red black,red green,white red
i don`t know where they go......
i know they are signals from the 4 diferent position 0,1,2,3 but the switch on the dashboard only has 2 wires!! so what do i need to do??? can someone help me here??
can someone look at their car or the headlight leveler motor and tell me what i need to do! lol its driving me nutz!
if i get some help i will send a nice hispanic girl!to you..!!!
lol...
if you have any information on this you can email me at gabesir@aol.com or reply
[Edited by gabewrx - 9/27/2002 4:31:51 AM]
yes i got the switch too . the one with 4 pins on the back
now i know 2 of those pins are for the little light inside the switch the other 2 are a signal in and signal out with a diferent voltage, so far i know that the system works on (-)ground
now on the headlight motor it has 6 pins : pin 5 and 6 are power (12v)red wire and pin 6 ground(-)black wire
and there is 4 more wires a blue,red black,red green,white red
i don`t know where they go......
i know they are signals from the 4 diferent position 0,1,2,3 but the switch on the dashboard only has 2 wires!! so what do i need to do??? can someone help me here??
can someone look at their car or the headlight leveler motor and tell me what i need to do! lol its driving me nutz!
if i get some help i will send a nice hispanic girl!to you..!!!
lol...
if you have any information on this you can email me at gabesir@aol.com or reply
[Edited by gabewrx - 9/27/2002 4:31:51 AM]
09 October 2002 | 06:57 PM
#6
Scooby Regular
Joined: May 2002
Posts: 87
Likes: 0
Gabe You are correct on pins 5 & 6
but you have the wrong levelling switch
The Sti uses an 8 pin switch of which 6 pins are used
The 6 pins used on the leveller switch are as follows
pin 1 NA
pin 2 feed from tail and illumination relay FB-11
pin 3 connects to pin 3 of both levellers blue/Yellow wire
pin 4 connects to pin 4 of both levellers red/green wire
pin 5 NA
pin 6 connects to pin 2 of both levellers red/black
pin 7 connects to pin 1 of both levellers white /red
pin 8 Earth black
Hope this helps you out
Now when can I expect delivery of the promised Latin lover .
but you have the wrong levelling switch
The Sti uses an 8 pin switch of which 6 pins are used
The 6 pins used on the leveller switch are as follows
pin 1 NA
pin 2 feed from tail and illumination relay FB-11
pin 3 connects to pin 3 of both levellers blue/Yellow wire
pin 4 connects to pin 4 of both levellers red/green wire
pin 5 NA
pin 6 connects to pin 2 of both levellers red/black
pin 7 connects to pin 1 of both levellers white /red
pin 8 Earth black
Hope this helps you out
Now when can I expect delivery of the promised Latin lover .
Thread
Thread Starter
Forum
Replies
Last Post