HT Autos 'PROJECT' Version 8 Spoiler Mould!!!!
#1
Former Sponsor
Thread Starter
iTrader: (24)
Join Date: Jan 2009
Location: Hyde Manchester
Posts: 1,364
Likes: 0
Received 0 Likes
on
0 Posts
HT Autos 'PROJECT' Version 8 Spoiler Mould!!!!
This type of mould has been 6 months in planning here at HT Autos and so far hes taken us a month to 'nearly' complete top half of spoiler.
Benifits of this system, is that we will be able to produce a spoiler far more superior to any GRP/FRP (fibreglass) replica's out there.
This system is the same that PRODRIVE used to manufacture all the production P1 spoilers and this project is being supervised by BRIAN GRAHAM ( the man who made the mould and all the original P1 spoilers).
It works using Polyurethane foam, which in a reacted state will expand about 30 times in volume, but with the help of 10 ton of pressure ,we will only let it expand less than twice, which will form about 2mm of rock hard plastic skin and a very dense urethane core, which is lightweight and extremely tough.
Pics so far ,below.......
Tooling on stand at angle of 15 degrees..
2.5 Ton toggle clamps...
Specially made adjustable hinges...
2500 newton rams...
There is more urethane in model than foam block....
This pic shows strength on 1mm section...
Hope this is of some interest to some of you?
Cheers for looking!
Mark @ HT Autos
Benifits of this system, is that we will be able to produce a spoiler far more superior to any GRP/FRP (fibreglass) replica's out there.
This system is the same that PRODRIVE used to manufacture all the production P1 spoilers and this project is being supervised by BRIAN GRAHAM ( the man who made the mould and all the original P1 spoilers).
It works using Polyurethane foam, which in a reacted state will expand about 30 times in volume, but with the help of 10 ton of pressure ,we will only let it expand less than twice, which will form about 2mm of rock hard plastic skin and a very dense urethane core, which is lightweight and extremely tough.
Pics so far ,below.......
Tooling on stand at angle of 15 degrees..
2.5 Ton toggle clamps...
Specially made adjustable hinges...
2500 newton rams...
There is more urethane in model than foam block....
This pic shows strength on 1mm section...
Hope this is of some interest to some of you?
Cheers for looking!
Mark @ HT Autos
Last edited by HT_Autos; 04 November 2009 at 06:15 PM.
Trending Topics
#17
Former Sponsor
Thread Starter
iTrader: (24)
Join Date: Jan 2009
Location: Hyde Manchester
Posts: 1,364
Likes: 0
Received 0 Likes
on
0 Posts
Bit more done today....
Finished boxing out........
Inlet feed in place......
Coat of High Temperature Epoxy Gelcoat to base.........
After 1st coat has dried to tack, second coat applied and also up sides....
When this has tacked off, 3 layers of multidirectional glass tape is applied with high temp epoxy resin.....
Mark
Finished boxing out........
Inlet feed in place......
Coat of High Temperature Epoxy Gelcoat to base.........
After 1st coat has dried to tack, second coat applied and also up sides....
When this has tacked off, 3 layers of multidirectional glass tape is applied with high temp epoxy resin.....
Mark
#20
Former Sponsor
Thread Starter
iTrader: (24)
Join Date: Jan 2009
Location: Hyde Manchester
Posts: 1,364
Likes: 0
Received 0 Likes
on
0 Posts
Pipework is buried in another layer of Paste Laminate.......
Next, hardware is put into place, which will support hinges, clamps ETC.
Then a mixture of Epoxy Resin, Binders, Chopped Fibres and sand is used to top up!.........
Mark
Next, hardware is put into place, which will support hinges, clamps ETC.
Then a mixture of Epoxy Resin, Binders, Chopped Fibres and sand is used to top up!.........
Mark