Fitted arb after some adjustment all ok

Going to look at a straight cut PPG box on sat hope all is ok as this was going to be my future work but has come up at a good price including rear diff .

Lee,You will love PPG:thumb:

Jura

Hope so mate

Straight to garage from work to cut out CF for gear lever surround easy ish job just gets rid of the heavy steel one used to attach centre consol

http://i2.photobucket.com/albums/y17...s/fb6a632d.jpg
http://i2.photobucket.com/albums/y17...s/4004a27a.jpg

Straight to garage from work to cut out CF for gear lever surround easy ish job just gets rid of the heavy steel one used to attach centre consol

http://i2.photobucket.com/albums/y17...s/fb6a632d.jpg
http://i2.photobucket.com/albums/y17...s/4004a27a.jpg

Looking very nice Lee:thumb:


Jura

Look and go even better when I get that gearbox in mate!

Whats the ratio's of the PPG Jura is it a longer first gear and less top end

Lee depends on ratios,but 1st is longer in our case and 70mph@5th at 2500RPM which is good for motorway,on drag strip we are changing before finish line to 4th at 115mph by GPS,hope this help


Jura

Found a link to ratio's on the PPG so il have to work it out should be a lot quicker out of corners

A few months ago I fitted the areocatch bonnet pins but couldn't get on with them so fitted standered bonnet pins and to be honest they are 10x better
http://i2.photobucket.com/albums/y17...s/e0883be1.jpg
http://i2.photobucket.com/albums/y17...s/3b863a98.jpg

We're used standard Sparco hoods pins and they're been spotless,looking very good


Jura

Just read most of the thread.. fantastic project.

Keep up the good work.

ps: what fog light covers are they and more importantly..where from?

cheers

My van went in for an mot and failed on ns bottom ball joint so replaced the lower arm and wheel bearing aswell had a spare hour do thought I would fit the pins took a bit of setting up but better job than the areocatches in my opinion .

Coming together really well now Lee,when will it get it's first outing do you think mate?

New clutch and a few other bits testing at Blyton very soon want to get it out to the sprint at Blyton on the 20th hopefully

A sneak preview on decals , I nipped down to spraybay just round the corner from where I work and had a chat with them on designs for my car we came up with this white rear rap with CDR Motorsport in red on the sides the logos will also be incorporated on the bonnet and boot with white flashes on Binet to break up the black.

Personally I think it will look good .

http://i2.photobucket.com/albums/y17...s/86bdce4d.jpg

Had a stand down day at work today so made good use of the time off and went down the garage (my second home intact if it had a shower and a kitchen I'd live there ) !!!

As my decals are now being made and will be fitted over the next week or so I need to get one job out the way which is the drivers rear arch is starting to bubble so removed the rear lights and bumper ready for sorting out as I don't want the vinyl rap just been used to cover up what lies beneath so on with the repair now.

I have kept my CDR sun strip but fitted the reis one I had which was kindly donated after a phone call to them explaining my situation .

http://i2.photobucket.com/albums/y17...s/d620f60c.jpg
http://i2.photobucket.com/albums/y17...s/d7ae9e3c.jpg
http://i2.photobucket.com/albums/y17...s/1cb11620.jpg

Lee looking good like is it,i wouldn't change the appearance of your car


Jura

The decals are going on mate out of curiosity if I don't like they can soon come off but a bit of advertising for john Cuddmore at CDR Motorsport .

The drivers side rear arch has seen better days the only real rust on it so was time to get the professionals in it started off like this
http://i2.photobucket.com/albums/y17...s/0b4f3dd1.jpg

Repair was done by cutting away rust and plating and spot welding in place then a little filler sand down primer and paint .
Just a little flattening off to do tommorow then good as new

http://i2.photobucket.com/albums/y17...s/9c355bf3.jpg
http://i2.photobucket.com/albums/y17...s/4970a2f5.jpg

Top job:thumb:

Good job Lee,get the fuel filler neck off and sort the rust on that before you have a leak though mate:thumb:

Won't be bothering with that Ryan as il be putting in a baffled tank it's not that bad actually but happy with the arch once flatted off should be 100% better.

All finished a few pics

http://i2.photobucket.com/albums/y17...s/07eaab17.jpg

http://i2.photobucket.com/albums/y17...s/6f7420c5.jpg

http://i2.photobucket.com/albums/y17...s/6d1c8cce.jpg

I then needed to get some air into the cab so had some 50mm plastic flexible conduit I found at work so routed this from under the front skuttle panel to drivers side under dash a vent cover will be used when I find one

http://i2.photobucket.com/albums/y17...s/a42885f6.jpg
http://i2.photobucket.com/albums/y17...s/edd638f0.jpg
http://i2.photobucket.com/albums/y17...s/ccb2f9c0.jpg
http://i2.photobucket.com/albums/y17...s/bad8cea4.jpg

Fitted rear tow strap today easy job really just front to do when it arrives

I used a 12mm bolt x40mm long to fasten the tow strap to the willans stress plate after drilling it out
http://i2.photobucket.com/albums/y17...s/7fddc877.jpg
http://i2.photobucket.com/albums/y17...s/ced0352f.jpg

I then marked out bumper from the back and drilled x2 10mm holes and slotted the bumper to allow the strap to come through

http://i2.photobucket.com/albums/y17...s/95d1e109.jpg
http://i2.photobucket.com/albums/y17...s/b1a2d309.jpg

Just the front to do now when it arrives.

Front strap has arrived so fitting that ASAP then to fit FPR on sat just injectors clutch and exhaust to go then ready for remap