Forged ej20 engine
#1
Scooby Regular
Thread Starter
Join Date: Aug 2010
Location: Northants
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
Forged ej20 engine
Forged ej20 complete engine just been rebuilt.
Closed deck block
Cosworth pistons
eagle rods
sti9 nitrited crank
acl bearings
new bottom end seal set
new top end gaskets
new timing belt and rollers
550cc injectors
new spark plugs
Whole complete engine bottom end and heads with inlet manfold and all ancillaries.
Open to offers
Also got a 6 speed gearbox for sale
Just testing the water as if to sell or not if i get enough intrest or not as im about to put the engine back in the car if not as its out at the moment as its only just been rebuilt.
Closed deck block
Cosworth pistons
eagle rods
sti9 nitrited crank
acl bearings
new bottom end seal set
new top end gaskets
new timing belt and rollers
550cc injectors
new spark plugs
Whole complete engine bottom end and heads with inlet manfold and all ancillaries.
Open to offers
Also got a 6 speed gearbox for sale
Just testing the water as if to sell or not if i get enough intrest or not as im about to put the engine back in the car if not as its out at the moment as its only just been rebuilt.
#3
Scooby Regular
Thread Starter
Join Date: Aug 2010
Location: Northants
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
Yes mate i have the diffs not sure if it jdm or uk i bought the car with it in it there is a problem with it though 3rd gear does crunch very slightly on hard driving but if driving normal its fine didnt bother me but as its not that bad but thought id say anyway, sorry forgot to mention this on first thread
Trending Topics
#10
ScoobyWorx
iTrader: (5)
Join Date: Oct 2010
Location: Barnsley SY
Posts: 768
Likes: 0
Received 0 Likes
on
0 Posts
same as above, who built the engine, this has a big bearing on price in my eyes and i may be intrested depending on your answer as its what im after and will be cheaper than me doing my own and then i have my engine to sell also that way
#12
Scooby Regular
Thread Starter
Join Date: Aug 2010
Location: Northants
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
Hi lads Im looking for £1500 it was built by my mechanic not a cowboy hes built about 4 or 5 scooby engines now i know you want to here the it was some one like alan jeffery or someone similar but just cost to much. The engine was recently rebuilt by scoobyclinic 10k ago but like a **** when i got it i ran it low on oil and spun a bearing. If you want to ring scoobyclinic up they know alot about this car they done loads of work on it ive got nearly 20k receipts from them. The reg is p7ruf if you want to ring them. The car was running 1.4 bar boost and 350bhp. Regards, Leo
#13
Hi Leo.
When you say you spun a bearing what exactly does that mean? Also when you did it did scoobyclinic repair it themselves?
The price you are asking doesn't somehow seem enough, I am extremely interested though, PM sent also.
When you say you spun a bearing what exactly does that mean? Also when you did it did scoobyclinic repair it themselves?
The price you are asking doesn't somehow seem enough, I am extremely interested though, PM sent also.
Thread
Thread Starter
Forum
Replies
Last Post
Sam Witwicky
Engine Management and ECU Remapping
17
13 November 2015 10:49 AM
Brzoza
Engine Management and ECU Remapping
1
02 October 2015 05:26 PM