More engine porn
#1
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
More engine ****
Brand new block. Billet crank. Cosworth rods and pistons.
Isn't it sweet?
And so clean!
Isn't it sweet?
And so clean!
#5
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
#7
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#8
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
#15
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
I wouldn't say it's an issue with an Impreza engine. A big heavy cast block might have some "give" in it, but not these light alloy ones.
It doesn't seem to matter with these if they are new or not, you invariably have to carry out some corrective machining which is why we always trial assemble first.
It doesn't seem to matter with these if they are new or not, you invariably have to carry out some corrective machining which is why we always trial assemble first.
#18
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
#19
Scooby Regular
iTrader: (2)
Join Date: Jul 2011
Location: Wisconsin USA
Posts: 192
Likes: 0
Received 0 Likes
on
0 Posts
I wouldn't say it's an issue with an Impreza engine. A big heavy cast block might have some "give" in it, but not these light alloy ones.
It doesn't seem to matter with these if they are new or not, you invariably have to carry out some corrective machining which is why we always trial assemble first.
It doesn't seem to matter with these if they are new or not, you invariably have to carry out some corrective machining which is why we always trial assemble first.
Also, the factoy doesn't catch all the little buggers of debris out of the block.
just a preference
#20
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
So you'd take the new engine out of your car, throw it away then fit a used one ?
Last edited by Alan Jeffery; 09 January 2012 at 07:47 AM.
#27
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
#28
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts
#30
Scooby Regular
Thread Starter
Join Date: Nov 2006
Location: Enginetuner.co.uk Plymouth Dyno Dynamics RR Engine machining and building EcuTek SimTek mapping
Posts: 3,662
Likes: 0
Received 0 Likes
on
0 Posts