P1 941 Project
#1
P1 941 Project
shes here
rolled off the trailer and the bumper decided to do arunner, it's okay just snapped the clips . Phew!!
initial assesment isn't to bad, will need the same done as i have done to mark's STI type R., but the shell underneath is solid.
Front windscreen aperture has rotten away exact same as my STI has.
rear windscreen surround has got a bit of rot setting in
Rear arches are bubbling up, but still solid and a relatively easy fix to do when underneath is stripped bare
brakes are all shot and missing pads.
interior is in dire need of stripped out and cleaned
ideally a full repray, however could get away with it for now once the rust around front and rear window's is sorted.
clutch has gone and is seized to the fllywheel,
however seems there's no big end knocking, sounds like clutch bearing has shat itself. so going to change the oil, filter and sump to make sure. BOOOST!! if it is shafted then hey ho not to bothered.
rolled off the trailer and the bumper decided to do arunner, it's okay just snapped the clips . Phew!!
initial assesment isn't to bad, will need the same done as i have done to mark's STI type R., but the shell underneath is solid.
Front windscreen aperture has rotten away exact same as my STI has.
rear windscreen surround has got a bit of rot setting in
Rear arches are bubbling up, but still solid and a relatively easy fix to do when underneath is stripped bare
brakes are all shot and missing pads.
interior is in dire need of stripped out and cleaned
ideally a full repray, however could get away with it for now once the rust around front and rear window's is sorted.
clutch has gone and is seized to the fllywheel,
however seems there's no big end knocking, sounds like clutch bearing has shat itself. so going to change the oil, filter and sump to make sure. BOOOST!! if it is shafted then hey ho not to bothered.
#5
yeah the arches will be cut out, there rock solid however they've started to bubble. so will be done in time
Here's some photo's of the not so good bit's overall.
Some pics of a hour spent this evening repairing the front bumper, the splitter had litterally " split " from the bumper in several areas.glued back in place,fibreglass filler then filled with finer finishing filler.
Here's some photo's of the not so good bit's overall.
Some pics of a hour spent this evening repairing the front bumper, the splitter had litterally " split " from the bumper in several areas.glued back in place,fibreglass filler then filled with finer finishing filler.
#7
Scooby Regular
Trending Topics
#13
Scooby Newbie
Join Date: Oct 2014
Location: Aberdeenshire
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
It was stored away to get attention at a later date, wasn't the cleanest when I got it.
Too many other projects resulted in the sale.
The engine does have the death knock Tom, no hiding that issue, if engine was fine I dare say it'd still be in the corner "rusting" away for another year, its getting a refresh now so all good.
Bang bang...
Last edited by a10ltr; 23 June 2016 at 06:21 PM.
#15
Scooby Regular
Join Date: Aug 2015
Location: Belfast
Posts: 102
Likes: 0
Received 0 Likes
on
0 Posts
It will, because no matter what happens you'll know exactly what you have.
Mine blew up as soon as I bought it but now it's back on the road and I'm out a fortune but I know it's good.
And was definitely worth the heart ache!
Good luck with the build buddy
Mine blew up as soon as I bought it but now it's back on the road and I'm out a fortune but I know it's good.
And was definitely worth the heart ache!
Good luck with the build buddy
#17
Well the above previous owner a10ltr is avoiding my messages etc. Said there was service history. However conveniently been binned, also was supposed to come with 18" rotas. Tried to arrange swap over with the shot rb5 alloys it came on. No answer and now blocked me all way. Hey ho.
Nothing happened to the p1 so far. Going to make a spit for it sooner or later so can get underneath sorted asap.
Anyone want 4 pots with discs and pads. Rb5 alloys and tyres .p1 bottom end bare. Ninja catback exhaust?
Nothing happened to the p1 so far. Going to make a spit for it sooner or later so can get underneath sorted asap.
Anyone want 4 pots with discs and pads. Rb5 alloys and tyres .p1 bottom end bare. Ninja catback exhaust?
#24
Well finally a little progress has started. Brought the car home due to a lack of space at work
Both inner arches around the strut top mounts have totally shat themselves. Got a few meters of 0.9 carbon steel to make up some new ones. Before hand going to strip down the suspension for easier access with the shot blaster cut and weld new metal and re seal.
Going to do one side at a time and take the time with it, don't want to lose heart with it being swamped in repairs required
The windscreen is very loose all the way round, pretty scabby underneath, plan on removing it tomorrow and get a better look at the a pillars.
The sills are in vgc considering, very solid and the 'lips' are still straight and unbeatable
Will get some photos up over next week or so
Will be mainly concentrating on getting the sti all roadworthy as it's all running properly ish now (maf issue)
Settle myself a target of till March next year to get all welding done and 2 solid and clean shells
Both inner arches around the strut top mounts have totally shat themselves. Got a few meters of 0.9 carbon steel to make up some new ones. Before hand going to strip down the suspension for easier access with the shot blaster cut and weld new metal and re seal.
Going to do one side at a time and take the time with it, don't want to lose heart with it being swamped in repairs required
The windscreen is very loose all the way round, pretty scabby underneath, plan on removing it tomorrow and get a better look at the a pillars.
The sills are in vgc considering, very solid and the 'lips' are still straight and unbeatable
Will get some photos up over next week or so
Will be mainly concentrating on getting the sti all roadworthy as it's all running properly ish now (maf issue)
Settle myself a target of till March next year to get all welding done and 2 solid and clean shells
#27
Tbh I have no idea what it's worth as is. . Probably not a lot and certainly worth building and repairing correctly as resale value is only rising
I'll be doing the rear turret welding myself. Already have materials here to do it. But for a garage probably 400 500 quid to do. I'll be replacing the rear arches as well so it's as solid as can be
#28
Well with the Sti nearly ready for the road after having new rear 1/4's done properly along with the sills. Partial respray until it's full respray next year. Can finally start pulling a few bits of the p1 and get a plan of action going.
Currently getting my shotblast set up finished up so plans are afoot to get this stripped bare and start with a she'll. After going threw it thoroughly the main concern is the shell
Full new roof skin as front edge is rotten and soft
Replace a pillar's as they have gone the same way as the stis and rotted threw
Replace both sills and rear outer 1/4's
Repair rear strut top towers on both sides as outer skin is a big hole
Might seem a bit of a long list however it needs done and would like to have the shell 100 percent perfect, will be fully blasting the underneath over the winter
However this car may not be as valuable as a original unwelded example it will be 100 percent solid and will last for next 20 years or so
Currently getting my shotblast set up finished up so plans are afoot to get this stripped bare and start with a she'll. After going threw it thoroughly the main concern is the shell
Full new roof skin as front edge is rotten and soft
Replace a pillar's as they have gone the same way as the stis and rotted threw
Replace both sills and rear outer 1/4's
Repair rear strut top towers on both sides as outer skin is a big hole
Might seem a bit of a long list however it needs done and would like to have the shell 100 percent perfect, will be fully blasting the underneath over the winter
However this car may not be as valuable as a original unwelded example it will be 100 percent solid and will last for next 20 years or so
#29
Well that's the back end all stripped and ready to be smashed to oblivion by billions of angry bits of shot.
I've tried uploading a walk around video of the back end however YouTube is a nightmare.
Diff all removed from the subframe, the frame is absolutely a death trap, scary to think how many others out there with the same problem.
This car is a prime example of firing undersea over a unprepped chassis. Even if it's been power washed and left to dry . Applying undersea over a unprepped chassis only leads to hiding and allowing rot to thrive.
With the likes of soda blasting nowadays being so gentle on metal, rubber, etc it's a no brainer to blast everything
Overall very pleased. After a lot of smacking with hammers and screwdrivers there's no new holes or bits to be worried about. Even the inner sill at the back have solid clean metal!!!!
Finally got YouTube to work and there should be vid here
I've tried uploading a walk around video of the back end however YouTube is a nightmare.
Diff all removed from the subframe, the frame is absolutely a death trap, scary to think how many others out there with the same problem.
This car is a prime example of firing undersea over a unprepped chassis. Even if it's been power washed and left to dry . Applying undersea over a unprepped chassis only leads to hiding and allowing rot to thrive.
With the likes of soda blasting nowadays being so gentle on metal, rubber, etc it's a no brainer to blast everything
Overall very pleased. After a lot of smacking with hammers and screwdrivers there's no new holes or bits to be worried about. Even the inner sill at the back have solid clean metal!!!!
Finally got YouTube to work and there should be vid here