Powerstation for Geo and Weighting?
#1
Scooby Regular
Thread Starter
Join Date: Dec 2005
Location: One step ahead of the bailiffs :-)
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
Powerstation for Geo and Weighting?
Hi,
Anyone care to comment (even by PM) on Powerstations competancies with geo and corner weighting please?
I have a non Scooby I want to run by them after new coilovers and my usual choice has become very expensive, and a long drive.
Cheers,
Steve.
Anyone care to comment (even by PM) on Powerstations competancies with geo and corner weighting please?
I have a non Scooby I want to run by them after new coilovers and my usual choice has become very expensive, and a long drive.
Cheers,
Steve.
#2
hello mate
i've used powerstation for some years now doin various jobs on previous cars i've had and never had any probs,to answer your question i had coilovers fitted by them to my astra gsi few years back and had them do a full geo set up i was very happy no problems
hope that helps
regards
nick
i've used powerstation for some years now doin various jobs on previous cars i've had and never had any probs,to answer your question i had coilovers fitted by them to my astra gsi few years back and had them do a full geo set up i was very happy no problems
hope that helps
regards
nick
#3
Scooby Regular
iTrader: (9)
Join Date: Oct 2006
Location: midlands
Posts: 2,316
Likes: 0
Received 0 Likes
on
0 Posts
had mine done 2 weeks ago and car handles well , they seem good and would use them again they are a little expensive tho 94 quid with vat an hour, i would recommend that u remove the track rod ends clean the thread and re-grease if they aint been off for a while,also i removed my bk seat before i went down so the could adjust the rear camber top mounts otherwise you will pay them to do this.It took them 35 mins to set mine up because i done all the above otherwise allow for 1-2 hours if the coilovers are already fitted.
#4
Scooby Regular
Thread Starter
Join Date: Dec 2005
Location: One step ahead of the bailiffs :-)
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
Man, that's a massive hourly rate.
Maybe my usual guy Chris Franklin at Centre Gravity is not so dear after all.
I think it was £500+ for an eight hour job including corner weighting.
Can Powerstation do corner weighting? They are a little slow to respond to email!
The car I'm aligning is a Honda S2000, so all on cams and a couple of rods.
Maybe my usual guy Chris Franklin at Centre Gravity is not so dear after all.
I think it was £500+ for an eight hour job including corner weighting.
Can Powerstation do corner weighting? They are a little slow to respond to email!
The car I'm aligning is a Honda S2000, so all on cams and a couple of rods.
#5
I've taken both my scoobs to powerstation and the extra hourly rate is well spent. I happily do a 180-mile trip to see them.
Phone them rather than email they're excellant so very busy, but they do pick up the phone.
They do have corner-weight scales but dont know if this is for their use or for setting up customer's cars.
Phone them rather than email they're excellant so very busy, but they do pick up the phone.
They do have corner-weight scales but dont know if this is for their use or for setting up customer's cars.
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Sam Witwicky
Engine Management and ECU Remapping
17
13 November 2015 10:49 AM